How to replace the Front Wheel Hub and Bearing 2006 - 2012 Ford Fusion 🚗

Find the parts used in the video on CarParts.com just there https://carparts.solutions/FUSION Over 1 million auto parts at your fingertips, download our app 🤖 https://carparts.solutions/AppGooglePlay or 🍎 https://carparts.solutions/AppIOS ⚙️ NEEDED CARPARTS AND PRODUCTS - Multi-purpose grease - Penetrating oil: https://carparts.solutions/PenetratingOil - Silicone grease - Wheel hub: https://carparts.solutions/FrontWheelHub_FUSION - Front brake backing plate: https://carparts.solutions/FrontBrakeBackingPlateD_FUSION and https://carparts.solutions/FrontBrakeBackingPlateP_FUSION - Wheel bearing: https://carparts.solutions/FrontWheelBearing_FUSION - Brake cleaner: https://carparts.solutions/BrakeCleaner 💪 TIGHTENING TORQUES - Upper ball joint nut: 35 Ft-lbs - Lower ball joint nut: 148 Ft-lbs - Brake caliper mount bolts: 66 Ft-lbs - Disc holding bolt: 10 Ft-lbs - Damper fork-to-lower control arm bolt: 76 Ft-lbs - Outer tie rod holding nut: 35 Ft-lbs - Wheel hub nut: 180 Ft-lbs - Wheel lug nuts 2006 through 2010 models : 98 Ft-lbs - Wheel lug nuts 2011 through 2012 models : 100 Ft-lbs 🛠 TOOLS The toolbox recommended by CARPARTS.COM to repair your Ford Fusion: https://carparts.solutions/ToolBox List of the tools we used to replace the Front Wheel Hub and Bearing on a Ford Fusion: - Hydraulic jack: https://carparts.solutions/FloorJack - Jack stands: https://carparts.solutions/JackStands - 17 mm wrench - 18 mm wrench - Ball joint puller - Chisel - Marker - Breaker bar - Circlip pliers - Hydraulic press - 40 mm bearing dismantling cup - 65 mm bearing dismantling cup - Long 10 mm socket - Wheel lug wrench - Abrasive sponge - Torque wrench: 20 to 250 Ft-lbs https://carparts.solutions/TorqueWrench_20-250 100 to 600 Ft-lbs https://carparts.solutions/TorqueWrench_100-600 - Ratchet - Flat head screwdriver - Thin flat head screwdriver - 10 mm socket - 15 mm socket - 23 mm socket - 32 mm socket - 8 mm socket - Torx T40 socket - 6mm Allen socket - Lineman's pliers - Needle-nose pliers - Hammer - Wire brush - Clamp or iron wire - Paper towels - Extender - Vice - Pin punch - Vise grips Don't forget to subscribe: https://www.youtube.com/@CarPartscomOfficial 🛻 COMPATIBLE VEHICLES The operation and tools displayed in the video should be available on the following vehicles : - 2006 Ford Fusion - 2007 Ford Fusion - 2008 Ford Fusion - 2009 Ford Fusion - 2010 Ford Fusion - 2011 Ford Fusion - 2012 Ford Fusion 📽 🛠 USEFUL VIDEOS 🛠 📽 - How to jack your 2006 - 2012 Fusion safely? ⬆ 🚗 : https://youtu.be/IumroE-E1qc ⚠️ CARPARTS.COM'S INFOS - We recommend loosening the nut on the end of the transmission once the vehicle is on the ground. If your vehicle is equipped with aluminum rims, you will need to remove the wheel first before you can remove the central rim cover. - When you change your wheel hub or your wheel bearing, we recommend that you also change your brake backing plate. - Don't forget to remove the cable that you used to hold the caliper assembly together. - We recommend replacing the hub nut with a new one. 🚨 DISCLAIMER This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area. 📚 CHAPTERS 0:00 Intro 0:10 Loosen the wheel hub nut 0:30 How to lift your Fusion 0:41 How do I do this ? 1:04 Remove the outer tie rod 1:33 Remove the strut fork bolt 1:58 Remove the ABS sensor 2:54 Remove the brake system 4:12 Loosen the control arms ball joints 5:11 Remove the wheel knuckle 5:51 Remove the wheel hub 6:12 Why you should also replace the backing plate 7:20 Remove the front wheel bearing 7:40 Clean the wheel knuckle 7:58 Replace the bearing 8:56 Put the backing plate back 9:13 Put the wheel hub back 9:45 Put the wheel knuckle back + tightening torques 10:59 Put the brake system back + tightening torques 12:39 Put the strut fork bolt back in + tightening torque 13:20 Put the outer tie rod back in + tightening torque 14:02 Put your Fusion on the ground 14:12 Tighten the hub nut + tightening torque